GC2
Failed GC2 Driver Installation
Problem: Your GC2 device is not communicating to your software or computer correctly. Explanation: Your device may be damaged. However, if this is not the case than you may have a failed USB driver installation for the GC2 device. This will be ...
GC2 Battery Care
Please read through the GC2 Battery Announcement, which suggests a discharge/recharge at least once a month. Suggested Battery Care: 1. It is highly suggested to continue to cycle charge your GC2 battery every two-three weeks to maintain conditioning ...
GC2 Power Supply Specifications
Failure to use a proper power supply may result in damages to your device. This can potentially damage the CPU Board within the device, which is a costly repair. To avoid this, we highly recommend to purchase this item from the Foresight Sports ...
GC2 Bluetooth Recommended Use and Standard Bluetooth Limitation Notice
Unfortunately, as with any wireless Bluetooth technology there is always the possibly for dropped connections. With the GC2 device we have mapped out a few items that should be kept for consideration should you be experiencing connection issues. ...
GC2 Driver and Firmware Installation - Including Original Firmware to New Firmware Steps
Should you experience trouble updating your GC2 firmware please consult the steps below: 1. If you are using outdated firmware the device may not connect to your computer. To begin, download and run to install the Original GC2 Driver Package : 1. ...
GC2 LCD Brightness
If you GC2 display appears too dim you may need to adjust the brightness. 1. Please take the GC2 device and hold down the Power button for 6 seconds to perform a hard restart. 2. From there, hold down the Brightness and Contrast button (little button ...
GC2 LCD - Displaying Solid Verticle Line
There are a few items that can be causing this: 1. The device needs to be powered by the AC Adapter. This vertical line may be indicative of a dead battery or the device loosing power. Powering from the AC adapter will allow you to verify this ...
GC2 Not Capturing
1. Confirm the GC2 Device Flash Module is Working Correctly: Please test the GC2 APART from software in the following fashion: With a flash module that is known to be working in a different GC2 device. Then test the flash module from this GC2 device ...
GC2 USB Troubleshooting
Your GC2 Device will not connect to the computer or within the software as expected. To Begin Troubleshooting the USB for a GC2 device follow the steps below: Note: These troubleshooting steps assume the device is functioning correctly and will ...
Resolving A USB Driver Connection Failure (Caused By Use of The Old GC2 Driver)
Foresight Sports USB Device Issues Two separate issues have been found relating to the Foresight Sports USB Drivers which affect Windows users. This document is provided in order to assist with diagnosing these issues and provide instructions to ...
GC2 Elevated Platform - Security Mount Instructions
Issue: Unclear Mounting Instruction or if GC2 does not fit properly on Elevated Platform. Reason: Proper seating of GC2 is required for device to stay on Elevated Platform correctly. Resolution: Use the following guide to ensure GC2 is properly ...
GC2 & HMT - Boot Error Code Troubleshooting
Some error messages on the GC2 or HMT will allow you a few trouble shooting steps that may save you from returning the item for diagnosis or repair. PLEASE NOTE: The GC2 and HMT devices are official at an End-Of-Life status. This means that the ...
What Temperature Can The GC2 Operate At?
GC2 Operating Temperature Range: Between 32F to 131F ambient (0 to 55C) The internal temp of the GC2 is is 10F greater than ambient temperature. Failure happens at around 160F internal (Published: PM - Nov 11, 2013) GC2 NOT WORKING DUE TO COLD ...
My GC2 Device Carry Distance Is Not Matching Within FSX And On The GC2 On Screen Data:
In some cases it may appear that the GC2 device is provide inaccurate data in the software while the Quad barometer setting is active. The issue is caused by having the “Use GCQuad Barometer” option enabled, but no GCQuad device connected. To adjust ...
GC2 - Solid Green Light & Nothing Visible On Display
If your GC2 device is powering on with a Solid Green Light but nothing is being displayed it may be caused by one of the following issues: 1. The GC2 display itself has a loose connection. To test this follow the steps below: Push up through the ...
If Windows computer is not recognizing the GC2 device
Confirm that the device is connected properly (USB cable is plugged in to both the unit and computer). Confirm that the USB cable is not damaged in any way. Confirm that the device has sufficient battery life (not applicable to GC2T/HMT/Kiosk). To ...
Diagnosing GC2 Battery-Based Power Issues:
If the GC2 does not remain powered on when not plugged directly into a power source. A battery issue may exist if the device immediately shuts off when not plugged into the AC adaptor. To begin, first confirm that the power adapter is working ...
Determining when the GC2 Flash Module Requires Replacement
Flash Modules are items that require occasional replacement. You may need to replace the flash device on your GC2 if your device is not recognizing shots (displaying dashes) or displaying inconsistent readings. 1. Remove device from any protective ...
Changing the GC2 On-Screen Units of Measurement
Once the GC2 device has fully powered on, select the left most arrow button on the front LCD panel. To select an option, navigate with the UP and DOWN arrow keys. To select the desired unit of measure, press the "OK" button until the setting appears. ...
If the GC2 Device Appears to Display Inaccurate Data
Confirm that the device is fully opened and the foot/latch is properly positioned underneath. Confirm the device is placed on the same level surface as the ball. (If applicable) Confirm that the protective shield (accessory) is properly attached and ...
The GC2 Does Not Display Some (or Any) Ball Flight Information
Test the device with a new flash module (or one you are certain is functioning). This will help determine if the flash module is the true cause of the issue. If the flash module is working correctly, please see "Ball Finding & Missed Shots" below. To ...
Understanding GC2 Ball Lock and Light Indicators
The on-screen ball placement aid is only displayed when the device is looking for a ball (the "ball-lock" indicator light will be flashing red). The ball must be placed within the right or left hitting zone (indicated by the trapezoids) for ball lock ...
If the GC2 Does Not Lock onto a Ball Placed Within the Hitting Zone
Confirm the ball is appearing within the hitting area on the LCD display. Confirm that the device is fully opened and the foot/latch is properly positioned underneath. Confirm the device is placed on the same level surface as the ball. Confirm ...
If the GC2 Device Does Not Recognize the Ball
Power off the GC2 device. If connected to a computer, disconnect the USB cord. Wait 5-10 seconds before powering device on again. Do NOT plug the USB cable into the GC2 at this time. Place a ball in the left or right hitting zone If the device ...
Connecting GC2 Device to an Android Device
On your Android device, go to the SETTINGS menu and select WIRELESS CONNECTION In the BLUETOOTH manager, turn Bluetooth on. While the GC2 is turned on, locate the SERIAL NUMBER of the device (located on the label underneath). Select the device with ...
GC2 Device Flash Module Operation Occuring Very Fast
If you are seeing that your device is operating in a state where the Flash Module is firing more quickly than you expected this may be due to the type of shot being taken. The device will adjust home many flashes is required to accurately take the ...
GC2 Serial Number Location
The GC2 Serial Number is located in two different locations: 1. The Product Sticker, located on the bottom of the GC2 device, includes relevant information about the device along with the Serial Number: 2. The Serial Number is also located in the ...
GC2 Product Support Page - System Resources, Manuals, and How to Use.
Foresight Sports has offered comprehensive online resources to our customers to understand how to use their GC2 device. Be sure to review the GC2 Product Support Page online to find all related items. This page will include user manuals, product ...
GC2 Bluetooth Code
When a code is needed for connecting the GC2 use '0000'